Jump to content

Cordless Mouse


epp_b

Recommended Posts

It happened again...my Logitech cordless mouse is starting to go funny on me.What happens is, it goes sparatic for a bit, then will only scroll up or down and be stuck on one side of the screen (either left or right, it's totally random). The strange thing is that nothing has been changed since this started as far as moving around electronic equipment. What I have near my receiver are: - Scanner - Monitor - Cordless keyboard (which is a set with the mouse, so it shouldn't be a problem) - Speakers - A radio (which is all the way across the room, a good 10 - 15 feet away) - UPS & Surge bar - Computer, of course ;)Has anyone else had problems with cordless mice going nuts? I e-mailed Logitech support and got nothing but a standardized useless response - and the support line -- which won't be open until maybe Monday -- is not toll free :D

Link to comment
Share on other sites

James M. Fisher

Does this behaviour happen 'on it's own', or just when you are trying to use the mouse? Have you tried a different mousing surface, or cleaning the optical 'eye'? :D I have heard of this happening to Logitech users from time to time, but I know of no solution. Sorry. My MS mouse is not problematic at all and I have the reciever between my monitor and a desktop speaker.

Edited by James M. Fisher
Link to comment
Share on other sites

Does this behaviour happen 'on it's own', or just when you are trying to use the mouse?
Both
Have you tried a different mousing surface, or cleaning the optical 'eye'?  :D
It's a ball-mouse, and I've tried it on different surfaces. I can tell by how it's behaving that 's definately something to do with interference.
I have heard of this happening to Logitech users from time to time, but I know of no solution. Sorry. My MS mouse is not problematic at all and I have the reciever between my monitor and a desktop speaker.
Hmmm... :D
Link to comment
Share on other sites

James M. Fisher

Sorry, I just assumed because it was cordless it was optical, too. D'OH! :D I supposed you have tried the latest drivers? Are you running this on Linux or Windows?

Link to comment
Share on other sites

Sorry, I just assumed because it was cordless it was optical, too.  D'OH! >_<I supposed you have tried the latest drivers?
No, but I'm pretty sure the drivers are irrelevant -- it's worked perfectly fine running with these drivers for a year & 1/2 until now.
Are you running this on Linux or Windows?
Windows 98SE
Link to comment
Share on other sites

No, but I'm pretty sure the drivers are irrelevant -- it's worked perfectly fine running with these drivers for a year & 1/2 until now.
Has the OS changed at all in the past "year & 1/2"? IE updates, Critical updates, DirectX updates, etc.Has anyone nearby installed a WAP or wireless network?
Link to comment
Share on other sites

I wouldn't rule out the drivers.If you installed any system update that could have modified files, it could have messed with the drivers.I know it may sound stupid, but have you tried a fresh set of batteries? Is the model you are using IR or radio wave? Do you have a portable phone near by? Got a microwave in an connecting room?etc.Edit: was typing before EdP posted... same point, system updates could have messed up the drivers. Or other interference.

Edited by Arena2045
Link to comment
Share on other sites

No, but I'm pretty sure the drivers are irrelevant -- it's worked perfectly fine running with these drivers for a year & 1/2 until now.
Has the OS changed at all in the past "year & 1/2"? IE updates, Critical updates, DirectX updates, etc.Has anyone nearby installed a WAP or wireless network?
No Wi-Fi, but there have been Windows Updates. That's a good point. Ill try re-installing the drivers.Arena2045: yes, I've tried new batteries, no cordless phone in the room, and no microwave anywhere nearby.
Link to comment
Share on other sites

Well, I tried reinstalling Logitech MouseWare (on a different bootable partition - gotta love PQMagic ;)), and it the "jumping" was bit more infrequent, but it was still jumping, nonetheless.On a side note: another reason I am doubting it has anything to do with software is because the receiver relies entirely on hardware. It is entirely possible to run a Logitech Keyboard and/or mouse perfectly fine without the iTouch or MouseWare - the software that the mfr's provide for mice and keyboard are strictly for customization. The basic functionality for keyboards & mice is provided by Windows. (BTW, the mouse still "jumped" without any MouseWare installed)Interestingly, I tried it on my laptop, which has a slightly newer version of MouseWare, and couldn't replicate the problem. However, to reiterate, I have used this version of MouseWare for a year & 1/2 without any problems. And I know someone else who uses this same version of MouseWare without any problems. I do NOT want to use the latest version as it exhibits some behaviours that I really don't like.Oh, and I can connect my corded optical mouse without any problems. If this were a software issue, I would expect my other mouse to act up as well.I have moved the received closer to the mouse (literally, 6 inches away), and, so far, better, but not perfect :(Might it make a difference that I have metal (aluminum, I think) sliders on my desk's trays? Again, I've had this desk since before I had the cordless keyboard & mouse, and have never had problems until now.

Link to comment
Share on other sites

Well if it's a sw problem there are options that can be done. Drivers, config settings, etc. If it's a hardware problem there's nothing that can be done other than replace the batteries and clean the rollers the ball rubs against. You've replaced the batteries, if you've cleaned the rollers, and ball itself, there's nothing left to try. You wore it out. :w00t: You need to buy a new one.You said you reinstalled the Mouseware, did you see if there were any newer Windows drivers that might help?Have you looked at Start>Control Panel>Mouse>Hardware>Properties>Advanced Settings? Maybe the Sample rate can be tweaked.

This might be a long shot, but could adjusting my monitor's brightness have anything to do with it?
Unlikely.
Link to comment
Share on other sites

Well if it's a sw problem there are options that can be done.  Drivers, config settings, etc.  If it's a hardware problem there's nothing that can be done other than replace the batteries and clean the rollers the ball rubs against.  You've replaced the batteries, if you've cleaned the rollers, and ball itself, there's nothing left to try.  You wore it out. :w00t:   You need to buy a new one.
Nope, I'll get it replaced on warranty then - still a year & 1/2 left!
You said you reinstalled the Mouseware, did you see if there were any newer Windows drivers that might help?
Tried that - nothing there. I can pretty much prove it's not MouseWare, because the problem occured without MouseWare even installed.
Have you looked at Start>Control Panel>Mouse>Hardware>Properties>Advanced Settings?  Maybe the Sample rate can be tweaked.
Nope, no sample rate setting - that's only with optical mice.
This might be a long shot, but could adjusting my monitor's brightness have anything to do with it?
Unlikely.
Nuts.
Link to comment
Share on other sites

This might be a long shot, but could adjusting my monitor's brightness have anything to do with it?Unlikely.
Nuts.
:) :) I also agree that it's not the MouseWare. But if you've got it under warantee still I'd get it into the mail ASAP. Let Logitech figure it out.To play with the idea of outside interference, cover the receiving unit with aluminum foil except for the antenna part. See if that helps. If you know anyone else with one it would be interesting to see if it experiences the same problems with your pc.Running out of ideas.
Link to comment
Share on other sites

Well, I was able to get my hands on another Logitech Keyboard & Mouse set which I borrowed from a friend and it has worked PERFECTLY FINE for hours!So this confirms that the problem is...

  • hardware related
  • NOT software
  • unlikely interference with other equipment
  • either a defective mouse and/or receiver, but more likely the mouse as the keyboard still works

Back to Logitech it goes! B)

Link to comment
Share on other sites

Great to hear that you have narrowed the problem to the hardware!

To play with the idea of outside interference, cover the receiving unit with aluminum foil except for the antenna part. See if that helps. If you know anyone else with one it would be interesting to see if it experiences the same problems with your
I was hoping that you would try the idea from EdP and send in a picture :flowers: I was going to recommend that you put the aluminum foil on your head. Similiar to the stylish headware that the kids in "Signs" were wearing B)
Link to comment
Share on other sites

James M. Fisher
Well, I was able to get my hands on another Logitech Keyboard & Mouse set which I borrowed from a friend and it has worked PERFECTLY FINE for hours!Back to Logitech it goes! B)
Good bit of trouble-shooting there! Software is usually the culprit, but not this time. Good thing it's still under warranty. :flowers:
Link to comment
Share on other sites

BTW, there is no antenna on the receiver - just a grey box.I'm glad it wasn't software - no-software solutions are always better, even if they take a bit more time.

Link to comment
Share on other sites

Well, good news - I tried it on my other computer again, and the mouse acted up this time! So Logitech will be shipping me a brand new keyboard & mouse set :)

Link to comment
Share on other sites

James M. Fisher
Well, good news - I tried it on my other computer again, and the mouse acted up this time!  So Logitech will be shipping me a brand new keyboard & mouse set :)
I don't know if you tried this- I didn't see it mentioned in the thread: did you reset the 'connect' buttons on the mouse and/or reciever unit?
Link to comment
Share on other sites

Arrrchchchcghghghghgh!!! I've just about HAD it with cordless devices! :thumbsup: My keyboard (the GOOD one that I borrowed from a friend because my other keybaord/mouse set wasn't working) disconnects every half-hour or so. Reconnecting is as simple as pressing the "Connect" button, but it's still very annoying <_<It hasn't started doing this until today.

Link to comment
Share on other sites

Hmmmm...too bad Logitech is already going to ship me a new set :thumbsup: Anyways, how is that possible? The receiver is sitting 5 inches away from the keyboard!

Link to comment
Share on other sites

Yes, I have a two radios (ghettoblaster & alarm clock) both a good 12 feet away from the computer -- but they're both off. Could it really interfere if the receiver is only 5 inches away from the keyboard & mouse?Refer to my first post for a list of other devices near the mouse & keyboard.

Link to comment
Share on other sites

Um...just a thought: I've (dis)connected the PS/2 cable(s) hot before - would this cause any problems (such as the problems I am having)? I know you're not supposed to do this with Win98, so I don't make a habit of it.On the other hand, I've had my PS/2 mouse disconnect by accident on my laptop (which runs Win98) several times before (because the PS/2 port is somewhat "loose-fitting") and I plugged it in hot and could use it again with no problems.To me, it doesn't seem like a problem that would be caused by this, but what do I know. :P

Link to comment
Share on other sites

Here's another far-fetched thought:Is it possible that, in hot-plugging my PS/2 devices, I damaged a part in my motherboard, which, in turn, causes the motherboard to incur damage to any device connected to its PS/2 port(s)?Please, somebody answer, getting desparate :thumbsup: (which is why I'm doing this at 11:50 pm!!!)

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...